Lime-cement plaster KS 50/50
Product description
The Fescon Tile Grout KS 50/50/600 is an air entrained, lime cement based dry mortar. The maximum grain size is 3.0 mm or 1,2 mm. The KS 50/50/600 tile grout is usually used as a filling plaster.
- Just add water
- Extremely weather-resistant
- Pumpable
- Breathable
Applications
- Burnt brick
- Lime-cement plastering
- Kahi-brick
The product is listed in the portal for building products that can be used in Nordic Swan Ecolabelled buildings.
Vinkki! Vieritä taulukkoa sivuttain
6416841560575
|
Lime-cement plaster KS 50/50 25KG 1,2 mm
|
56057
|
25 kg
|
6416841360571
|
Lime-cement plaster KS 50/50 1,2 mm
|
36057
|
1000 kg
|
6416841530578
|
Lime-cement plaster KS 50/50 3 mm
|
53057
|
25 kg
|
6416841330574
|
Lime-cement plaster ks 50/50 3 mm
|
33057
|
1000 kg
|
Base
The adhesive plaster (Fescon KS 10/90/600 or KS 35/65/500) must harden for at least one day before filling. If necessary, wet the base before applying the filler.
Mixing
Refer to the bag for how much water the plaster requires. Add the dry material to the water and mix with a concrete mixer for around ten minutes. With a power mixer or a drill paddle, around one to three minutes of mixing is sufficient. Let the plaster stand for around ten minutes and mix it again for a short while. Find the correct consistency at this stage by gradually adding the rest of the water. We do not recommend adding all of the water right at the start. Every batch must be mixed in the same way. The finished plaster remains workable for around two to three hours.
Work instructions
Apply the filling plaster with a plaster trowel or a pump. A suitable thickness for one layer of filler is around 15 mm. If the layer thickness exceeds 20 mm, the filler must be applied in several layers so that the previous layer has had time to dry for one to two days before the next layer is applied. In dry conditions, the base must be wetted before applying a new layer of plaster. Screed the filler plaster with a board. You can also carefully float the surface with a wooden tool to level the surface. Usage of dry plaster with a layer thickness of 15 mm
is approx. 30 kg/m². The lowest working temperature is + 5°C.
You can use plastering mesh to reduce the cracking risk caused by the drying of the plaster. You should in particular use a mesh at the joints of different materials, as reinforcement near openings and corners, and when plastering various block surfaces (Siporex, LECA, concrete).
After treatment
A fill plastering should be given aftercare for at least three days. The aftercare must be begun as early as possible so that plastic cracks in the fresh plaster can be prevented.
Waste handling
Storage and handling of waste. See the separate storage and disposal instructions https://www.fescon.fi/en/material-bank
Material usage |
approx. 30 kg/m² with a 15 mm layer thickness |
Water requirement |
4.0 - 5.0 l/25 kg |
Finished compound |
13-14 l/25 kg |
Maximum grain size |
3 mm or 1,2 mm |
Package size |
25 kg and 1000 kg |
Storage |
storage time in a dry location approx. 1 year |
Workability time |
2-3 h |
Air content |
approx. 15% |
Frost resistance |
flexural and compressive strength do not decrease after 200 melt-freeze cycles |
Flow/plasticity |
Hägermann 170 mm |
Water retention capacity |
80- 90% |
The information is based on tests and practical experience. We cannot affect conditions at the work site so we cannot assume responsibility for the end result affected by local conditions.