Facade coating JSP 1.5

Ask for more information

Product description

The Fescon Facade Coating JSP is a polymer-modified cement-based coloured thin-layer plaster that contains additives improving its weather resistance and reducing capillary water absorption. Suitable for spray and manual application. The maximum grain size is 1.5 mm. 

  • Easy to use
  • Good grip on the base
  • Good workability characteristics
  • Separate adhesives not required
  • Spray-applied
  • Chloride-free
  • Excellent weather resistance
  • Breathable


  • Concrete and brick facades
  • Surfaces treated with cement-based levelling or finishing plasters

N.B. Not suitable over organic paint or an elastic joint.

The product is listed in the portal for building products that can be used in Nordic Swan Ecolabelled buildings.
EAN code Product name Product number Package size
6416841450869 Facade coating JSP 1.5 mm Fescon 235 45086 25 kg
6416841016065 Facade coating JSP 1.5 mm Fescon colors 45150 25 kg

Remove old coatings and paint, for example by water sand blasting. Also roughen any new concrete surfaces by water sand blasting. Clean the surfaces of dust with a pressure washer. Repair any damaged concrete. The patch surfaces must be left as coarse as possible. Allow the patches to harden for at least one or two days before coating. If the base has dried up, wet it until it is darker in colour. The best time to wet the surface is the previous night. Before starting work, apply a test coating to ensure the structure and tint. The tint is affected by, for example, the absorption characteristics of the base, the consistency of the mass, the coarseness of the surface, and naturally the sprayer itself (nozzle size and air volume), and the spraying method used.


Check the water requirement of the coating from the bag. Add the dry material to the water and mix with a concrete mixer for around ten minutes. With a power mixer or a drill paddle, around one to two minutes of mixing is sufficient. Allow the coating to stand for around ten minutes and mix it again for a short while. Find the correct consistency at this stage by gradually adding the rest of the water. We do not recommend adding all of the water right at the start. The finished coating remains workable for around two hours.

Work instructions

The Fescon Facade Coating is sprayed using a levelling spray or a funnel top sprayer. It can also be spread manually using a steel trowel or a brush. The first layer is sprayed to a thickness of 1-3 mm and
the second to a thickness of around 1-2 mm. The first layer must be allowed to harden for at least one day before the next spraying.

Spray the last layer using mass that is as dry as possible in good weather conditions. Dark colours require greater care than light colours when spraying. We recommend spraying contiguous surfaces at the same time. You should "hide" the working seams in corners, expansion joints or, for instance, behind drainpipes. There may be some differences in the tint of different manufacturing batches, so we recommend ordering the required amount of coating all at once. With a plaster spray, the spraying distance is over 1 m, and with a funnel top sprayer, around 0.6 m. Spray using circular motions perpendicularly to the surface. The water-soluble salts in the cement and the salts formed during the hardening of the lime may rise to the surface with moisture and appear as efflorescence. Heavy rain soon after the coating, internal moisture in the structure, thermal leakage and insufficient ventilation cause efflorescence. The risk can be reduced by protecting the fresh coating from rain. For the same reason, the new facade should be allowed to dry for at least one heating season before coating.

After treatment

In very dry conditions, the coated area must be protected with a plastic film or light spraying of water (the water must not flow) for at least one to three days.
When the temperature is:
+20°C, protect the fresh coating from rain and strong sunlight for one day
+10°C, protect the fresh coating from rain for three days
+5°C, protect the fresh coating from rain for seven days

Service instructions

A dirty surface treated with Facade Coating can be cleaned with a pressure washer. Remove any damaged spots and repair the holes. No water should remain on the base after cleaning. Facade Coating or Stone Colour S paint can be used for recoating. The work instructions for the product used must be followed during coating and painting work. One treatment is normally sufficient for a cleaned, undamaged surface. Two or more treatments are needed for damaged areas from where the coating has been removed or holes have been patched.

Storage and handling of waste
See the separate storage and disposal instructions https://www.fescon.fi/en/material-bank

Material usage

1 mm layer 2 kg/m²

Water requirement 3.5 - 5.0 l/25 kg
Type powder
Colour as per colour chart
Maximum grain size

1.5 mm

Package size 25 kg

storage time in a dry location approx. 1 year

Layer thickness

2-5 mm

Lowest usage temperature


Workability time 2 h
Plasticity (Hägermann) approx. 200 mm
Compressive strength

approx. 20 MPa

Adhesion strength

> 1.5 MPa

Flexural bond strength > 4.0 MPa
Linear expansion coefficient

< 15 x 10-6/0C

Fire class A1

 approx. 4.0 mm (91 days, expedited test)

Air content approx. 15%
Frost resistance no damage in 100 cycles
Water retention capacity approx. 95%