Contact us
+358 20 789 5900 or with form
Offer request 0
Masonry mortar M100/600
Masonry mortar M100/600 Winter
Compact mortar M100/600
Compact mortar M100/600 Winter
Compact mortar Heavy M100/600
Compact mortar Heavy M100/600 Winter
Winter-time masonry mortar TML
Block mortar M100/500
Block mortar M100/500 Winter
Stone adhesive KVL
Mortar for tongue-and-groove blocks PHL
Mortar for tongue and groove blocks PHL Winter
ELT Brick element grout
ELK Clinker element grout
« Back to the product group

Masonry mortar M100/600 Winter

Ask for more information

Product description

Fescon Masonry mortar M100/600 Winter is as cement-based mortar for burnt and sand-lime brick facade masonry in winter conditions in the temperature range -15°C...+5°C. The maximum grain size is 2.0 mm. For brickwork repointing and for repairing mortar joints. For cold flue parts in chimney masonry, such as in cold attics and above the roof, as well as for the masonry of the outer brick shell of the fireplace. 

Applications

  • For facade masonry in winter conditions
  • For brick work jointing and jointing of natural and slate stones on vertical surfaces
  • For repairing existing mortar joints
  • For cold flue parts in chimney masonry, such as in cold attics and above the roof
The product is listed in the portal for building products that can be used in Nordic Swan Ecolabelled buildings.
GTIN code Product name Product number Package size
6416841330703 MASONRY MORTAR M100/600 WINTER 33070 1000 kg
6416841340009 MASONRY MORTAR 39 QUARTZ WHITE WINTER 34000 1000 kg
6416841340016 MASONRY MORTAR 59 BIRCH BARK WHITE WINTER 34001 1000 kg
6416841340023 MASONRY MORTAR 40 LIME GRAY WINTER 34002 1000 kg
6416841340030 MASONRY MORTAR 41 GRAIN YELLOW WINTER 34003 1000 kg
6416841340047 MASONRY MORTAR 42 BRICK RED WINTER 34004 1000 kg
6416841340054 MASONRY MORTAR 45 EARTH BROWN WINTER 34005 1000 kg
6416841340061 MASONRY MORTAR 46 PEAT BROWN WINTER 34006 1000 kg
6416841340078 MASONRY MORTAR 48 BLACK GRAY WINTER 34007 1000 kg
6416841340085 MASONRY MORTAR 52 LINEN LIGHT WINTER 34008 1000 kg
6416841340306 MASONRY MORTAR 44 SAND BROWN WINTER 34030 1000 kg
6416841340221 MASONRY MORTAR 71 SWAN WINTER 34022 1000 kg
6416841340252 Masonry mortar 72 Ali Winter 34025 1000 kg
6416841340276 MASONRY MORTAR 73 CUCKOO WINTER 34027 1000 kg
6416841340153 Masonry mortar 74 Hawk Winter 34015 1000 kg
6416841340269 MASONRY MORTAR 75 LARK WINTER 34026 1000 kg
6416841340207 MASONRY MORTAR 77 JACKDAW WINTER 34020 1000 kg
6416841340245 MASONRY MORTAR 79 PTARMIGAN WINTER 34024 1000 kg
6416841340290 MASONRY MORTAR 80 SIBERIAN JAY WINTER 34029 1000 kg
6416841340115 MASONRY MORTAR 81 TEAL WINTER 34011 1000 kg
6416841340214 Masonry mortar 82 Capercaillie Winter 34021 1000 kg
6416841340320 MASONRY MORTAR 83 WILLOW GROUSE WINTER 34032 1000 kg
6416841340122 MASONRY MORTAR 85 RAVEN WINTER 34012 1000 kg
6416841340139 Masonry mortar 86 Hazel hen Winter 34013 1000 kg
Base
  • The temperature of the masonry brick or structure is above > -15°C
  • Brick, natural stone, slate
  • Brick pallets are protected from rain. The bricks must not be wet or covered with snow or ice.
Priming
  • Masonry structures are not primed
Mixing and application of the product
  • Masonry work should not be carried out in direct sunlight, in the rain or during strong winds.
  • The working temperature should be between +5°C and -15°C. The joint effect of wind and frost must be taken into account.
  • A bag (25 kg) of dry powder is mixed with 3.0 to 3.5 litres of clean water. 
  • Do not add all the water at first. The mixture contains the correct amount of water when the mortar holds its shape and no water rises to the surface.
  • The amount of water must be as instructed in the product card. Deviating from the recommended amount of water lowers the mortar’s strength properties, increases the risk of separation, affects the strength development and reduces workability. 
  • Product is mixed with a mortar stirrer, in a concrete mixer, or with a pan-mixer or a continuous mixer to a smooth consistency. The maximum mixing time is approx. 10 minutes.
  • If the working conditions are very dry or warm, it is possible to improve the adhesion by dampening the masonry joints or bricks. There should not be water drops on the substrate.  
  • Keep the amount of water the same during jointing, because any variations in the amount of water will show as colour differences in the joint.
  • The jointing technique affects the density of the mortar joint. Finish the jointing by sealing them with a brick jointer and removing any excess mortar from the brickwork by brushing diagonally over the joints with a masonry brush.
  • The expansion joints are provided as defined in the structural plans.
  • The working time of the mortar is about 1 hours. 
  • When finished working, wash the tools immediately with water.
  • Remove any dried mortar mechanically.
  • After casting, you should keep the mortar joints moist at temperatures below 0°C by fog spraying for about 3 days, depending on the conditions or the site.
Repointing to a previously masonry joint
  • Available in 20 standard colours. Special colours are subject to order.
  • When repointing, the old mortar must first be removed to a depth of at least 20 mm, but no more than 15% of the masonry depth or according to the designer’s instructions.
  • The joint is cleaned of dust and dampened.
  • When repointing, add the dry powder to the instructed amount of water and let it stand for about 10 minutes. After that, remix the paste and add masonry mortar to make the paste semi-dry. This mixing method ensures the sufficient air content of the mortar.
  • When repointing, start first with vertical joints and after that work with the horizontal ones. Repoints that are over 20 mm are done in two phases.
  • The working time of a semi-dry mortar for repointing is 1 to 2 hours.
  • After casting, you should keep the mortar joints moist at temperatures below 0°C by fog spraying for about 3 days, depending on the conditions or the site.
  • Bases or masonry units with low water absorption are repointed with Repairing plaster KL 1.2 or Facade coating JSP 1.5.

 

Other points to note
  • Construction planner instructions and official regulations are to be followed in all masonry work.
  • Not suitable for masonry of the inner shells of fireplaces or wood-burning stoves nor masonry of chimney flues indoors.
  • Masonry mortars may have slight differences in shade between small and big bags, as well as between the mortars intended for winter and summer time masonry, so it is not advisable to change the type of mortar in the middle of the wall.
  • When the temperature drops below -15°C, the masonry area should be covered for seven days to prevent it from freezing.
  • Winter products will be available in the winter season, from 15 September to 1 March. At other times, the products must be ordered separately.

Storage and handling of waste
See the separate storage and disposal instructions https://www.fescon.fi/en/material-bank

Material usage

approx. 1.2 kg/MRT
approx. 1.5 kg/NKH
approx. 1.7 kg/NRT
Water requirement 3.0-3.5 l/25 kg
Finished compound 13 - 14 l / 25 kg bag
Type powder
Binder cement
Colour available in 20 standard colours, special colours subject to order
Maximum grain size

2.0 mm
Package size 1000 kg
Storage

storage time in a dry location approx. 1 year
Additives

additives to improve workability and weather resistance and reduce the freezing point of water
Usage temperature

-15°C…+5°C
Workability time 1 h
Compressive strength

M 5
Adhesion strength

≥0,16 N/mm2 (SFS-EN 998-2, 5.4.2 a)
Reaction to fire A1
Heat conductivity 0,72 [w/(m•K)], P=50%
Chloride content < 0,1 % (EN 998-2:2016)
Water vapour permeability

µ 15/35
Water absorption by capillarity

0,2 kg/(m2 · min0,5) (EN1015-18)