Fast Mortar XtremeRapid XR

Kysy lisätietoa

Tuotekuvaus

 

Fast mortar XtremeRapid XR is an exceptionally fast cement-based compound. The product’s setting time is approx. 10 minutes, and the working time approx. 4–5 minutes. Suitable for installing fence posts without additional supports, and can be used for repairing concrete structures and for rapid castings. The rapid mortar can also be used in winter due to its fast strength development. By adjusting the amount of water, the product can be mixed into a paste-like or a pourable consistency. For indoor and outdoor use.

 

  • Extremely fast setting
  • Hand-applicable
  • Workability adjustable with water amount

Käyttökohteet

 

 

  • Installation of fence posts without additional supports
  • Repairs of concrete structures
  • Rapid castings where the structure must be put into use immediately
  • Repairs and sealing of concrete wells

 

GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841531070 PIKALAASTI XTREMERAPID XR 25 KG 53107 25 kg

 

Substrate

  • The substrate may be a concrete surface, a formwork, or, in fence post installations, a ground pit.

Concrete substrates

  • The substrate must be clean, solid, and free from dust.
  • Loose layers, cement laitance, and other contaminants must be removed mechanically to ensure proper adhesion between the product and the substrate.
  • Smooth concrete surfaces must be roughened.
  • The substrate must be sufficiently strong, stable, and load-bearing.
  • The temperature of the concrete surface to be repaired must be above +5°C.
  • In winter conditions, it must be noted that the product cannot be applied onto frozen concrete, as frozen concrete lacks the water absorption required for proper adhesion. When cast into a formwork or ground pit, this is not an issue.

 

Priming

  • No bonding primers are used with this product.
  • Priming is performed by moistening the substrate with water approx. one hour before application. The surface must be matt-damp; no free water may remain on the substrate.

Instructions for use

  • Mix one 25 kg bag of dry powder with 3.0–3.3 litres of cold water.
  • With a low amount of water, the mix becomes moldable; with a normal amount of water, it becomes pourable.
  • Use warm water when working below +10°C, and hot water in freezing conditions.
  • Do not overdose water, as this weakens the product’s strength properties.
  • Mix thoroughly into a homogeneous mass using a drill mixer. Mixing time 1.5–2 minutes.
  • Apply the product to the working surface with a suitable tool.
  • Working time approx. 4–5 minutes after water addition.
  • Clean tools immediately after work with water.
  • Hardened product can only be removed mechanically.

Covering

  • The product may be left uncovered or uncoated.
  • The product’s strength properties and other technical characteristics make it suitable as a substrate for most materials.

 

Curing

  • The product does not require curing.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

 

Approx. 2 kg/m²/1 mm

Vedentarve 3.0 - 3.3 l / 25 kg
Valmista massaa 11–11.5 litres of mortar from a 25 kg sack
Olomuoto Powder
Sideaine Special cement
Väri Grey
Maksimiraekoko

1.2 mm

Pakkauskoko 25 kg
Varastointi

1 year in the original packaging in a dry place

Kuitu Not fibre-reinforced
Lisäaineet

Additives that improve workability

Käyttölämpötila

See instructions for use

Työstettävyysaika Approx. 4-5 minutes
Kävelykelpoisuus Approx. 10 minutes
Puristuslujuus

C 30

Taivutusvetolujuus F5 (EN 13813)
Palokäyttäytyminen A1
Pakkasenkestävyys Frost-resistant, for indoor and outdoor use
Vedenkestävyys

Water-resistant

Vastuunrajaus, tuotteen käyttöön liittyvät huomiot ja rajoitukset: Tutustu Fescon Oy:n yleisiin toimitusehtoihin ja tuotteeseen liittyviin suunnittelu- sekä työohjeisiin.