Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Floor compound LM 6000
Underfloor heating filler LL 5500
Coarse floor levelling compound LM 5000
Floor levelling plaster LT 4000
Floor concrete LB 7
Fescorapid
Fescofine
FlowPlan
Flow CS
Flow FS
Flow GS 3.0 mm Gypsum floor mass
Flow Primer
Primer PLUS
Elevation mark
Edge strip 30x30x2000 mm
Bordering strip 8x150 mm
Separation fabric 1.5x50 m
« Takaisin tuoteryhmään

Flow Primer

Kysy lisätietoa

Tuotekuvaus

Brush-on primer for surface pretreatment before floor levelling. Flow Primer improves the adhesion of floor levelling compounds, reduces or eliminates the formation of air bubbles, and prevents water contained in the floor levelling compound from being absorbed into the surface too quickly. For indoor use. 

  • Brush-on primer for floor plasters
  • Dries quickly
  • Easy to spread
  • High spreading capacity
  • Make pumped levelling plasters easier to spread
  • Prevents the creation of air bubbles

Käyttökohteet

  • Hollow-core slabs
  • Cast-in-place concrete floors
  • Cement-based levelling compounds
  • Plasterboards and chipboards
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841769053 FLOW PRIMER 10 L 76905 10 l

Base 

  • The substrate must be clean, solid, and dust-free, and vacuumed.
  • Loose layers, cement laitance, and other impurities must be removed mechanically to ensure proper adhesion.
  • The substrate must be sufficiently strong, dimensionally stable, and load-bearing.
  • The base floor structure temperature must be > +10°C and the relative humidity < 95% RH.
  • The relative humidity of the base structure affects the drying time of the floor screed.

Mixing ratio

  • Concrete surfaces and surfaces with cement-based levelling: 1 part Flow Primer, 3 parts water
  • Surfaces that cannot withstand moisture, e.g. plaster and wood surfaces: Use undiluted
  • Mix before use by swirling the package; avoid shaking

Applying the primer

  • Flow Primer is applied as a thin, even layer by brushing. The primer must not be allowed to form puddles.
  • The Primer must be dry before the floor levelling compound is applied (1 to 4 hours, depending on the conditions)
  • Highly absorbent surfaces (e.g. cast-in-place concrete floors) are primed twice.
  • If air bubbles form in the surface of the floor levelling compound, it usually indicates insufficient priming
  • Wash tools and equipment with water immediately

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

Hollow-core slab surfaces: finished mixture (mix ratio 1:3) about 10 m2/l
Cast-in-place concrete surfaces: finished mixture (mix ratio 1:3) about n. 5 m2/l
Plaster and wood surfaces (undiluted): about 7 m2/l
Olomuoto Liquid
Pakkauskoko 10 l container
Varastointi

In a cool room, not below +6°C, up to 1 year in a hermetically sealed original container
Käyttölämpötila

+10°C...+25°C (base floor structure and room temperature)
Kuivumisaika

1-4 h depending on the conditions
Ohenne Water
Levitystapa Brushing
Kuljetus Warm transport
Vastuunrajaus, tuotteen käyttöön liittyvät huomiot ja rajoitukset: Tutustu Fescon Oy:n yleisiin toimitusehtoihin ja tuotteeseen liittyviin suunnittelu- sekä työohjeisiin.