Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Waterproofing compound
Waterproofing compound WS
Fescoseal A+B
Adhesion promoter
Primer KP
Waterproofing strip
Drain flange 300x300 mm fibre
Drain flange KL-B
Waterproofing accessories FS
Waterproofing accessories VE
Tile adhesive plaster VSL
Tile adhesive plaster ILL
Tile adhesive plaster SS2
Tile adhesive plaster SSL Lite
Tile seaming plaster SML
Sanitary silicone
« Takaisin tuoteryhmään

Tile seaming plaster SML

Kysy lisätietoa

Tuotekuvaus

Fescon Tile Seaming Plaster SML is a dry mortar with a cement binder, max. grain size 0.3 mm. Certificate No. VTT-C-870-06.

  • Easy to use
  • Good workability characteristics
  • Good adhesion and tightness
  • M1 classification

Käyttökohteet

  • Grouting of Dutch, clinker, mosaic and other ceramic tiles both indoors and outdoors
  • Joint width 2-6 mm.
Tuote on listattu Pohjoismaisen Ympäristömerkinnän rakennustuotetietokantaan ja sitä voidaan käyttää Joutsenmerkityissä rakennuksissa.
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841671004 LAATTASAUMALAASTI SML VALKOINEN 3 KG 67100 3 kg
6416841204004 LAATTASAUMALAASTI SML VALKOINEN 15 KG 20400 15 kg
6416841671011 LAATTASAUMALAASTI SML MARMORINVALKOINEN 3 KG 67101 3 kg
6416841204011 LAATTASAUMALAASTI SML MARMORINVALKOINEN 15 KG 20401 15 kg
6416841671028 LAATTASAUMALAASTI SML HARMAA 3 KG 67102 3 kg
6416841204028 LAATTASAUMALAASTI SML HARMAA 15 KG 20402 15 kg
6416841671035 LAATTASAUMALAASTI SML VAALEANHARMAA 3 KG 67103 3 kg
6416841204035 LAATTASAUMALAASTI SML VAALEANHARMAA 15 KG 20403 15 kg
6416841671042 LAATTASAUMALAASTI SML TUMMANHARMAA 3 KG 67104 3 kg
6416841204042 LAATTASAUMALAASTI SML TUMMANHARMAA 15 KG 20404 15 kg
6416841671073 LAATTASAUMALAASTI SML VAALEA BEIGE 3 KG 67107 3 kg
6416841204073 LAATTASAUMALAASTI SML VAALEA BEIGE 15 KG 20407 15 kg
6416841671127 LAATTASAUMALAASTI SML BEIGE 3 KG 67112 3 kg
6416841204127 LAATTASAUMALAASTI SML BEIGE 15 KG 20412 15 kg
6416841671110 LAATTASAUMALAASTI SML MUSTA 3 KG 67111 3 kg
6416841204110 LAATTASAUMALAASTI SML MUSTA 15 KG 20411 15 kg
6416841671134 LAATTASAUMALAASTI SML MUSTANHARMAA 3 KG 67113 3 kg
6416841204134 LAATTASAUMALAASTI SML MUSTANHARMAA 15 KG 20413 15 kg
 Pretreatment of the base
  • The surface must be clean, undamaged, dust-free, and level, and the slabs must be firmly attached to the base.
Mixing
  • Refer to the bag for how much water the plaster requires.
  • Mix into a consistent mass with a power mixer or a drill paddle for around one to two minutes.
  • Allow the plaster to stand for around ten minutes, and then mix again for a short while and find the right consistency by adding the rest of the water; adding all of the water right at the start is not recommended.
Grouting
  • Check that the tiling mortar does not extend over the centre line of the tile seams. If necessary, remove excess mortar with a suitable method.
  • Spread the grout obliquely over the seams with a rubber trowel, pressing down hard enough to fill the seams. Depending on the conditions, allow the seams to dry for 20 to 40 minutes, after which you can clean the tiles with a moist sponge.
  • Avoid excessive use of water so as not to flush away the dye in the seam and the grout itself.
  • During cleaning, shape the seams, fill them, and compact them to the desired appearance using, for example, a wooden stick or rubber trowel.
  • Once the tile surfaces have dried, use a dry rag to perform final cleaning.
  • The working temperature must be above +10°C.
  • You may not start grouting the floor until at least one to three days and the wall until at least one to two days after the tiling.
  • We recommend protecting unglazed tiles with tile protectors before grouting.
Aftercare
  • The joints must be wetted with clean water two or three times during the first day. This prevents the joints from drying too quickly, eliminating shrinkage cracking and achieving a tight joint.
  • The drying temperature of the tiling should be above +10°C.
  • Underfloor heating should not be switched on during the drying period of the plaster.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

consumptions with a 4 mm joint thickness:

  • floor tile 100 x 200 x 7 1.1 kg/m2
  • floor tile 200 x 200 x 8 0.9 kg/m2
  • wall tile 150 x 150 x 5 0.8 kg/m2

 

 
Vedentarve 0,33 l /kg of plaster powder
Sideaine cement
Runkoaine lime filler
Väri white, marble white, light beige, dark beige, light grey, grey, dark blue-grey, dark grey, light blue, brown
Maksimiraekoko

0.3 mm
Pakkauskoko 3 kg, 15 kg
Varastointi

sack: storage time in the dry location about 18 months

bucket: storage time in the dry about 2 years
Lisäaineet

casein-free plastic polymer, additives to improve hydrophobic and workability characteristics, iron oxide colours
Käyttölämpötila

+10°C...+25°C
Puristuslujuus

> 15  MPa (EN 12808)
Taivutusvetolujuus > 3.5 MPa (EN 12808)
Kutistuma

< 2 mm/m (EN 12808)
Pakkasenkestävyys frost-resistant
Vedenimukerroin

water absorption capacity < 5 g/30 min (EN 12808)