Ota yhteyttä
020 789 5900 tai Lomakkeella
Tarjouspyyntö 0
Joint filler SF
Bedding plaster LF
Bedding plaster LF RD
Finishing plaster LRF
Finishing plaster LRF RD
Brick bedding plaster TTF
Bedding plaster VF
Finishing plaster VHF
Levelling compound for wet areas WTT
Filling plaster TLR
Indoor lime-cement plaster SR 7
Gypsum plaster mix GL
Wall surface strengthening membrane
« Takaisin tuoteryhmään

Filling plaster TLR

Kysy lisätietoa

Tuotekuvaus

The Fescon Filling Plaster TLR is a quickly hardening and drying filling plaster for interior wall surfaces and dry, humid and wet areas.

Käyttökohteet

  • Wall and ceiling surfaces in dry, humid and wet areas
  • Suitable for straightening, conduit filling and patching of concrete, plaster, block surfaces, lightweight concrete, sand-lime bricks and burnt brick surfaces
  • The finished surface is suitable for a tiling base, and it can be waterproofed with Fescon Waterproofing Compound
  • On old paint surfaces, the Fescon Tile Adhesive Plaster is used as the adhesive plaster
  • The filling plaster cannot be used for floor levelling, soft lime cement plastering or surfaces levelled with a water-soluble compound
  • If necessary, can be overlaid with Fescon wall levellers
Tuote on listattu Pohjoismaisen Ympäristömerkinnän rakennustuotetietokantaan ja sitä voidaan käyttää Joutsenmerkityissä rakennuksissa.
GTIN-koodi Tuotenimi Tuotenumero Pakkauskoko
6416841201089 TÄYTTÖLAASTI TLR 20 KG 20108 20 kg
Base

The surfaces must be solid, clean and dust-free. Carefully remove weak and loose material. Before applying the plaster, use water or Fescon Primer to wet dry and water-absorbent bases.

Mixing

Refer to the package for how much water the plaster requires. Add the dry material to water and mix with a drill paddle or other suitable mixing tool for around one to two minutes. The finished plaster remains workable for around 20-30 minutes.

Spreading the levelling compound

Spread the levelling compound on the base either with a levelling spray or a steel trowel. You can recover and reuse any extra compound. When applying several layers of the levelling compound, allow the previous layer to harden completely before applying the next layer. Depending on the conditions, the hardening will take one to two days. If necessary, the dried surface is ground after the application of each layer of levelling compound.

Coating

Can be overlaid or waterproofed after around 24 hours. 

After treatment

In dry conditions, wet the levelled surface with a water spray.

Varastointi ja jätteen käsittely
Katso erillinen varastointi ja hävitysohje https://www.fescon.fi/materiaalipankki

Materiaalimenekki

1 mm layer approx. 1.5 kg/m²
Vedentarve max. 3.8 l/25 kg
Olomuoto powder
Sideaine portland cement, aluminate cement, gypsum
Runkoaine Limestone powder and natural sand. Limestone powder contains small amounts of quartz, but the weight content of alveolar quartz is less than 1%, so the product is not classified as harmful in terms of quartz.
Väri grey
Maksimiraekoko

1.2 mm
Pakkauskoko 20 kg
Varastointi

storage time in a dry location approx. 1 year
Kerrospaksuus

overlaying 5 - 30 mm, partial levelling 5 - 50 mm
Alin käyttölämpötila

+10°C
Työstettävyysaika 20-30 min
Päällystettävyys Can be overlaid or waterproofed after around 1 day from plastering. Relative humidity of the base < 85% RH
Kovettumisaika

approx. 1 day at +20oC, approx. 3 days at +10oC
drying time depends on layer thickness and the humidity in the drying area
Tartuntalujuus

> 0.5 MPa (for a concrete surface)
Vedenkestävyys

waterproof
Päästöluokitus meets the requirements of emission class M1 for building materials